- #Mtsx labtool r03.00.02 serial
- #Mtsx labtool r03.00.02 update
- #Mtsx labtool r03.00.02 archive
- #Mtsx labtool r03.00.02 upgrade
- #Mtsx labtool r03.00.02 full
#Mtsx labtool r03.00.02 upgrade
The result is many existing upgrade tools (PCON Plus, Depot RSS, Lab RSS, etc.) will no longer work with the MTS2000 radio. To protect against illegal software copying and/or radio upgrades, Motorola is implementing "TOOLPROOFING" into the MTS2000 radio at the Florida factory beginning 2/27/95. To date, 9,000 units have been upgraded in the field. Motorola has been shipping FLASHport software upgrades on the MTS2000 radio since September of 1994. Potential Problem Radios MTS2000 Models Only with firmware 5.42 or greaterĬause Implementation of Toolproofing in release 5.42 and greater Subject MTS2000 Programming Sources - Unauthorized Tool Usage The following information was passed along to me and is a potential hazard if you use LAB RSS:įrom Radio Network Solution Group/Product Services, Plantation Program it up the way you want and program the radio. Set everything else the way you want or think it should be.Ĭreate yourself a blank (default) codeplug and program it into the radio. MY_MT2000) and in the Maximum Channels field, enter 255. All you need to do is create a model profile (with any model number you want ie. This software will let you create your own model profile and then a blank codeplug. What you have to do is get your hands on a copy of the MT2000 LAB RSS. I don't know if the software will let you program more than 160 modes into the zone lists though, under the Radio Wide Information the software still reports 160. So your radio won't work as well until it is retuned.Īn additional note, the Version 4.00 software will let you add modes beyond 160 in the Add Personality screen. You reprogram it, the reprogramming effort changes tuning data all to default write down the tuning data from the radio before.for each zone you add after 10, you loose oneĬhannel (11 zones gives you 254 channels).MT2000 unless you can create a model profile identical to a "normal" there is no way of going back to a "normal".you will not be able to clone this radio to any.you will not be able to program any old saved.Your radio, it becomes an individual radio once you create your own model profile and program.NOTE:There are a couple of things you should be aware of before you undertake this project: The problem is getting the radio to do it. It appears that all A7 model MT2000's are capaple of doing 255 modes rather than the 160 they are shipped with. This may be a little too scary for some of you to want to attempt but. The cable you need is the standard MTSX programming cable.
#Mtsx labtool r03.00.02 update
Now, the update for this software is RVN4097M R06.00.00 05 Sept 97, which should mean that it should program the radio as well. The RVN4097F ver R02.10.01 RSS package specifically shows it programs the following radios: MT/MTS2000 MTX838/8000/9000. If you are trying to program a MTX-838, from what we've heard, you need to use the MTSX software. If you have the accessory adapter for the side connector on the radio, the typical schematic of the speaker mic looks like this. You set SYSTEMWATCH to the Spectra with RIB mode (works best). The radio DOES NOT have to be programed to the system you want to watch. NOTE: When the radio is in the RF MODEM mode, it will do a self test and then the screen will go blank. You can put the radio into RF modem mode from the F4-F4-F4 (Trunking Config). Most MTS2000/MTX8000's only have a 256k controller, which will not work. Firmware version has to be above 5.44 (which has a 512k controller in it). You can run system watch using a MTS2000 handheld. For HMN4044, HMN4047, NMN6209, and NMN6210 microphones, set both dip switches toward the
#Mtsx labtool r03.00.02 serial
Microphone you are using has a manual PTT or serial data PTT.įor HMN1035 and HMN1056 microphones, set both dip switches toward the front
Located on the bottom rear corner of the MTVA holder. If you have the MTSX Convertacom (MTVA), you will notice that there are two DIP switches
However, you can clone a Type II code plug into a B3 radio and it will work just fine. There were a few B3's that were Type II produced by Motorola.
#Mtsx labtool r03.00.02 full
If it is an MTX8000 and has a front mounted display with either a 6 button or full keypad, you have a radio that will do Type II. If you are (un)lucky enough you might find an F3 modem that does Type II. Just remember to beware of the Toolproofing error.īoth the MTX8000 B5 & B7 models are Type II Trunking.
#Mtsx labtool r03.00.02 archive
You need to read an archive for a MTS C7 and program it into the MTX. Well, it looks like so far, the only way to convert a MTX B5 or B7 into a MTS C7 is to use Lab RSS. Have a look at the MTSX series model breakdown Upgrading your MT2000 from 160 to 255 modesĬhanging band limits in all MTSX RSS versions
0 kommentar(er)
